Canon, the Canon logo, and imagePROGRAF are trademarks or registered Ink used for maintenance purposes such as head cleaning is absorbed. (Replace. Complete The Survey. No, Thank You. Canon · Consumer Product Support imagePROGRAF Series Support – Download drivers, software, manuals. Products. imagePROGRAF iPF Drivers & Downloads; Manuals; NEED SERVICE? imagePROGRAF iPF Specifications · Drivers & Downloads · Manuals.
|Published (Last):||9 July 2009|
|PDF File Size:||2.93 Mb|
|ePub File Size:||20.6 Mb|
|Price:||Free* [*Free Regsitration Required]|
The lamp is lit if the Ethernet cable is connected correctly and communication is possible between the computer and printer. F Note on installing the upper rear cover 1 Fit four rear-panel screws  into screw holes on the right side. Page Chapter 3 7 Raise the ink tank lock lever and remove all ink tanks.
The part of the caps that comes into contact with the face plate of the nozzle assembly is made of rubber. Both PCBs hold vital information, such as settings and a carriage drive time.
If Canon cannot fix your Product’s malfunction through remote diagnostics, Canon shall schedule an on-site service call by an independent authorized Canon Service Provider the “Service Provider” or Canon will send you a replacement part for any defective user replaceable item.
Canon iPF Series. Service Manual. Parts Catalog
Page servicf Go. Chapter 3 4 While aligning the triangle marks at the back of the printer with the triangle marks at the back of the stand, place the printer on the stand.
Periodic Maintenance Chapter 5 5. I have read and understand the information above, and wish to download the designated software. Page Chapter 4 – To remove the carriage unit, pull it out of position keeping the carriage unit level with care not to harm the linear scale. Image processing unit This unit converts the RGB multi-value image data or CMYK multi-value data received from the host computer through the interface connector to the binary image data for canoon ink colors used.
Don’t apply the grease to locations other than those designated. Image processing unit This unit converts the RGB multi-bit image data manusl CMYK multi-bit data received from the host computer through the interface connector to the binary image data for the ink colors used. Page Chapter 3 d. Chapter 2 c Pump The pump suction pump is a tube pump that pressurizes the ink tubes with rotating rollers to generate a negative pressure for sucking inks.
Canon imagePROGRAF iPF9000
Media Width Cut sheet Roll Feed. The print time is measured from the start of printing until the image is exited out from servive printer. Keep the belt stopper, screw, and the hex wrench which have been removed since these are needed when moving the printer to another location later.
Page 92 Chapter 1 3 Push in the left and right Basket Rods toward the back all the way, until they stop. You must cooperate with Canon in remotely diagnosing the Products malfunction. When the printhead is secured to the carriage, the ipf9000 contact of the head relay PCB is pressed against that of the printhead to convey print signals. Do not remove or cut them.
Flaws on the linear scale could result in malfunctioning. Don’t show me this message again. Chapter 3 6 Insert the basket rod in the middle of the basket cloth in the hole  on the bottom of the rod holder, and thread the black cord from the back through the hook  on the top of the rod holder.
Basic Operation Outline Chapter 2 2.
Saving print jobs will offer the following benefits: Want manuak register this product? F 8 Disconnect five flexible cables from the carriage relay PCB. Feed roller bearing  F 4. Ink Tube Unit Chapter 4 4. Canon warrants the Product to be free ipf0900 defects in workmanship and materials under normal use and service for a period of one 1 year after delivery to the original purchaser “Purchaser” by Canon or its authorized dealer.
Page Chapter 5 – Do not dry the interiors of the top cover with a dry cloth. Table Of Contents Contents 4. Do not reattach the protective cap 2 to the printhead ipd9000 the cap may damage the nozzles. Page Chapter 2 2.
Feed roller HP sensor The feed roller HP sensor detects transitions from white transmittedor a reference, to black shielded when the printer is switched on, thereby setting the home position of feed roller eccentricity correction. Maximum Media Roll Diameter 59 feet 18 meters. To do so, keep pinch roller  pressurized to ease to work of phase align- ment during gear installation. F 9 Pull the basket rod  at the front of the basket unit all the way out and lift the rod to lock the rod in place.
Table of Contents Add to my manuals Add. Enter text from picture: The sensor detects the presence of paper when it receives sensor light reflected upon the paper.
Chapter 1 3 Push in the left and right Basket Rods toward the back all the way, until they stop.