ENSONIQ EPS SERVICE MANUAL PDF

This page contains information about the Service Manual for the EPS Plus from Ensoniq Corporation. Hello Gslutz, im searching for schematics for the Ensoniq EPS Can someone help You wont find the service manual for free on the web. 21 EPS—16 PLUS Service Manual Table of Contents — 1 Table of Contents . For more information about the Poly-Key Keyboard assembly, see ENSONIQ.

Author: Yorg Tojasar
Country: Burkina Faso
Language: English (Spanish)
Genre: Life
Published (Last): 9 January 2010
Pages: 434
PDF File Size: 4.93 Mb
ePub File Size: 3.77 Mb
ISBN: 230-2-61992-571-8
Downloads: 70796
Price: Free* [*Free Regsitration Required]
Uploader: Kazranris

ENSONIQ EPS 16 PLUS SERVICE MANUAL Pdf Download.

Reverse Cross Fade Attach the new main board power cable to the power supply at J4 and to the main board at J1 0. Remove the two screws that fasten the metal cartridge retainer to the base and discard the screws and the retainer.

Remove the four 4 self-tapping screws from the top of the unit closest to the control panel. Eject the test disk and then press Load. When the keyboard is tuned, all LEDs should go out. If a solder short occurred on the bottom side of the board, it will be necessary to remove the keyboard in order to remove the main board and repair the short see the EPS Service Manual for disassembly instructions.

Re-attach the Wheel Assembly to the case using the four screws. Loosen the serviice threaded mounting studs on the D-type connector.

Carefully tip the unit enspniq its rear panel. Remove the two 2 screws and nuts that secure the Power Supply to the case note that there are star washers on each screw.

  JOE SATRIANI SIGNATURE LICKS PDF

To Load A Bank Attach the metal plate to the new Disk Drive using the two screws and star washers. With the EPS facing you, remove the four control panel screws with the hex wrench.

Install the new KPC board onto the standoffs making sure the side of serfice board with the pin connector is closest to the base of the unit. The plate is attached with two screws and accompanying star washers This plate must be installed to ensure proper operation of the drive. Analog Test Page a.

Select a sound to save back to disk. Attach the control panel to the base see Section B. Remember, updating the EPS is as easy as copying a disk.

ENSONIQ EPS MUSICIAN’S MANUAL Pdf Download.

When ennsoniq the Communication Test Board, keep in mind that it is sensitive to static discharge. Esp Effects Test See Rack Hardware Notes items 3 and 4 on p. Press Edit, then double-click on Instrument. Extended the acceptable range of Mod wheel and other analog inputs. Make Loop Longer Punching In” On A Track After deleting one note you realize that three notes have been deleted. Press Cancel-No when you are done the sample. Discard the cartridge cover.

Ensonlq the five 5 15 mm nuts from the rear panel jacks marked Ft.

The format is shown below: Checking The Software Version Remove the Disk Drive see Section H and check the datecode on the label on the top side of the drive. Install the four 4 machine screws and star washers into each side of the unit the ones that could attach the mounting ears. This means it will be very difficult to remove this connector by just pulling.

  LM044L LCD PDF

Therefore, isolate the desired wavesample s as follows: If you must, wrap the entire unit in plastic first. Plug the Stereo to Stereo cable into the Headphones and Ft.

Ensoniq EPS 16+ Service Manual

Press the key into the pressure zone and verify that pressure causes a pitch bend. If M readings are off, then it is most likely that there is a problem with the Main Board. Remove the two temporary screws from step 5 that are holding the Memory Expander PC board to the bottom housing.

Reconnect the pin ribbon cable to the KPC board before sliding the new assembly into place. Hall Reverb, 44khz Reverb, Room Reverb Install die two 2 self tapping screws on either side of the unit 3.

Reinstall the Power Supply screws. This will prevent a faulty option from complicating your troubleshooting. How to program an arpeggiator in your sampler Watch out for them, and please don’t pull on the wires!

Plug the Dual Footswitch into the Ft. The display will read: Get the inside scoop on what makes your sampler tick, learn what’s not covered in the manuals, pick up a multitude of sound design tricks, learn how to optimize your sampler for live performance or studio tracking, learn how to master your SCSI setup, and much, much more.